Can anyone come up with an ID for this lock other then cheap Chinese mass produced? Just curious honestly. I know it was bought once upon a time at Walmart so not very quality.

Bonjour à tous !

Je débute en crochetage et suis confronté sur deux serrures que je tente d'ouvrir actuellement a une "protection anti-crochetage dans le rotor" qui consiste en une goupille haute suivie immédiatement d'une goupille basse. Cette protection a-t-elle un nom particulier ? Et auriez-vous des astuces pour passer cette difficulté ?

Merci à tous!

I am looking for a set or individual tools for gutting locks. There are some discussions around mokis huk set but I saw the gut wrench on sparrows. So my question is - should I go for the huk or get the wrench with tweezers, mini mat and followers?

Wrench https://www.sparrowslockpicks.com/products/the-gut-wrench

Mini mat https://www.sparrowslockpicks.com/products/mini-pinning-mats

Followers https://www.sparrowslockpicks.com/products/plug-followers

Tweezers https://www.sparrowslockpicks.com/products/pinning-tweezers

HUK set https://mok-workshop.de/en/products/huk-schlossdemontage-set

We are updating language under Rule 5 - Off Topic to better outline what is considered an off topic post.

r/lockpicking is a sub dedicated to hobbyist lockpicking and locksport and all posts should be related to those topics. While picking installed locks, emergency lockout advice, and other topics are covered under then own rules, Rule 5 is intended to cover other non-locksport posts. These include posts asking for opinions on if a lock was picked (e.g. I found this outside my door, is it a lockpick? Do these scratches mean someone tried to pick my lock?), and asking for security advice (I need a new door lock, what is hard to pick? How should I secure my bike? What's a good safe?).

Under the previous wording there was some confusion regarding posts asking for recommendations on locks to practice picking - these posts have always and will continue to be allowed. That said, it's a frequent question and searching the sub for previous answers before posting is recommended.

First off I’d like to say that unless anything changes I don’t plan on doing any submissions for belts as it’s not something I’m interested in. But I just wanted to share that I finally figured out my Ace 38mm brass padlock! I opened it by luck yesterday when I was trying it for about an hour, but I spent around 2 and a half hours going through every little variation till I finally figured it out. I know it’s only a green belt but before I went and took a long break from lockpicking a while ago I couldn’t even open a yellow belt with TOK tension so I take this as a big win. And if anyone else wants to share their little victories in the comments feel free to! Sorry for the random post btw it’s just about 2 a.m. where I am so I have no one to share this with.

These appear to be branded and have none of the usual Paclock stamps, other than on the key. The packaging indicates 90A but I wasn't expecting the PR1 keyway. 6 pins with a mix of spools and serrated + 1 standard. u/PAC_PREZ any insight on their origin story?

Thank you!

I spent so much time thinking about what it would be like to pick my first lock then my Jimy Longs intermediate picks came in the mail. I grabbed some small random lock from the junk drawer and got right to it. Definitely was harder than I imagined. I tried to visualize the components but it took a me a solid 10 minutes before I bust that thing open.

I’m looking forward to learning as much as I can and having fun along the way. This is just one of those hobbies I know will be hard to explain to my friends and family.

After taping 2 rotations and screwing in set screws, I couldn't get the key easily in and then couldn't get the key out without removing the screws.I think and confirmed that the screws pushed some of the springs in too far to allow the driver pin to come up above the shear line. I had to use different length driver pins and springs, even cutting a shorter spring in half to make it work. Two things to consider: 1. the end combination length of driver pin plus spring to reach just to the bottom of the newly tapped area of the cylinder, 2. each key plus driver pin lengths together have to get above the shear line. Picts of original longer driver pin and my shorter replacement, and my shorter spring and even a cut spring to make things work. With the shorter pins and springs the key works fine and the lock can be picked.

I have next to no experience with picking dimple locks. I've got three in my collection so far; two have spool pins and the third is an ABUS 75IB/50, which as I understand has spools, torpedoes, and requires float picking.

Does anybody have any recommendations for simpler dimple locks that I can practice on before tackling dimples with spools?

Thanking you all in advance. Apologies if this breaks Rule 5, but I've seen other people asking for recommendations, so I'm going to post it anyway.

#PACLOCK200KCLUB @PACLOCK

No idea what i'm doing, literally got this pickset and lock 30min ago. Lock is an Abus 54ti/30.

Any tips where to buy locks for cheap? I'm based in Finland so most used locks i see online are Abloy disc-detainer locks. Quick glance at the discord lock bazaar didn't help either.

The first lock I picked is a Master lock #1 Commercial. I had fun doing it with a rake over and over. I will practicing single pin picking so I can understand it better until I can get a lock that is a little more difficult. Any reccomendations on the next lock I should try? I'm using Jimy Longs 0.019 Basics.

So this my key is locked in an open lock. Everything is locked and I cannot move the top part. Any ideas?

Grabbed this a while back thinking a master lock with spools would be "gg ez". Turns out I was wrong, but not because the lock was actually difficult.

It was me. I made assumptions which led to a vicious cycle of frustration and overthinking. This thing made me rage quit multiple times and it was all my own fault.

Long story short, turns out sometimes you need to check your ego and respect the lock regardless of what you think you know or how good you think you are. If I just took my time and actually concentrated properly in the first place instead of thinking "master lock lol", then getting annoyed with it when it didn't behave as expected, this whole fiasco could have been avoided. It most likely would have opened the way I started out if I'd just taken my time and actually concentrated on the pins properly, and had a bit of patience 🤪

The rundown for anyone interested:

I tried picking this one like any other master lock at first, BOK tension with a .040 and JL short hook. Got a nice false set and kept losing it, assumed pin 6 was causing oversets (because I'd seen the key, mini lesson sometimes this does more harm than good). So I switched to my usual TOK with pins down configuration, using the wrench I made specifically for american padlocks. Didn't like the feedback but persisted. Tried a medium hook. Gave up. Tried BOK again, switching to the PN06 hook and a few different wrenches, thought maybe the core was binding up.

Decided maybe TOK pins up was the way to go. Tried an ergo turner, nope. Made a wrench similar to the JL ones which applied tension nicely but still no dice. Out of desperation I clamped it in the vice and used a regular prybar, still nothing. I tossed this lil guy to the side and came back to it randomly here and there, giving up out of annoyance relatively quickly each time.

Then today I decided to chill out, concentrate properly, and treat it with respect.

BOK with the short end of a .050, PN06 hook. Put the thought of oversetting out of my mind, stopped thinking about pin 6 altogether, decided to just focus on feedback and lighten up a bit. And most importantly, pick position and slowing down.

Got into false pretty quickly. Went light going against the CR and just let the pins do what they wanted. Literally back to front it was click click click open. Less than a minute.

Welp.

Sometimes you actually do need to concentrate on an "easy" lock... this is something I should know all too well by now but my attitude caused me more problems than the pins ever could. Don't be like me and keep this in mind at all times 🤣

I know this was long but if you're a new picker and struggling with a certain lock maybe this will give you some motivation or something. I've been picking locks for a long time and got my ass kicked by a master lock because I thought I was too good for it. Every day a school day apparently!

(This TED talk brought to you by me waiting on lunch)